Radio Type Approval, Homologation, Certification Services - Global Market Access Solutions
We can offer you our reliable Type Approval services in Japan. Our distinguished contact with the authority in Tokyo, as well as our experience in the homologation of consumer as well as automotive RF-products and Short Range Devices (SRD) in ISM-Frequency band will make way for your trouble-free and cost-effective market access in Japan.
We will assist you to put your product successfully on the market by offering the following services:
Identify applicable requirements for your specific product or technology feature to comply with current regulations in safety, EMC, wireless, etc.
Provide pre-compliance testing during the design and development phase to determine compliance
Assist in completion of applications and other required forms
Test in our accredited labs or your qualified facilities to issue Test Reports and Certificates according to national standards
Handle entire submittal process including working with local testing and certification organizations
Coordinate verification testing on qualified products as needed
Facilitate and expedite project progress with support of IB-Lenhardt AG local team
Support renewal maintenance of certificates as required
User manual translation service on demand
We can offer you a short-termed tentative offer based on a Datasheet of the device: quote@ib-lenhardt.de
Marking of Certification Logo or Number Required?
Yes
Size
diameter 3 mm (or greater) mm
Specific User Manual Requirements?
No
News for Japan
MIC working on development of 920 MHz RFID regulation
Active low power wireless systems in the 920MHz band are widely used for mobile identification (RFID), smart meters, sensor networks, etc.
In recent years, narrowband communications (LPWA), which can transmit power over long distances, are becoming more widespread as sensor networks. In Japan. this system is equipped with a carrier sense function to share the frequency between the systems, while in other countries, frequency hopping and low duty cycle functions are in use. Therefore, the need for harmonization with other countries is increasing.
In light of these needs, the Ministry of Internal Affairs and Communications studied the necessary technical conditions for the introduction of a system that does not require a carrier sense function. Based on this report, the MIC decided in January to develop regulations for 920 MHz RFID.
To provide better WLAN connections Japan plans to amend its regulation. The changes are scheduled for summer 2018 and focuse on the 5 GHz frequency. Effectively it will provide better compatibility with other regions, further details can be found in the draft.
Updated Labelling Requirements for Radio Devices
Japan’s Ministry of Internal Affairs and Communications (MIC) recently revised its labeling regulations to accommodate smaller devices with size restrictions.
More simplified labelling is allowed as below:
Simplification of the Certification number - Under the prior scheme, the label code was comprised of the CAB code (first three digits), followed by reference to the category of the specified radio (WW) and a 10-digit certification number given by the CAB. Under the new scheme, the category of the specified radio (WW) is no longer required to be printed on the label and the certification number given by the CAB has dropped from 10 to 6 digits.
Use of electronic label - For devices with a screen, such as a phone, the label can be displayed on the screen instead of being printed on a physical label on the device.
These changes come in addition to another recent change which allows CABs to issue a single certification number to cover a product with multiple radios, where previously separate certification numbers would have been granted instead.
Description
The Type A electrical plug (or flat blade attachment plug) is an ungrounded plug with two flat parallel pins. Although the American and Japanese plugs appear identical, the neutral pin on the American plug is wider than the live pin, whereas on the Japanese plug both pins are the same size. As a result, Japanese plugs can be used in the US but often not the other way around. The pins on Type A and Type B plugs have a hole near the tip that fits into ‘bumps’ found on the contact wipers of some sockets, so that the pins are gripped more tightly allowing for better contact and also to prevent the plug from slipping out of the socket. Some sockets have spring-action blades that grip the sides of the pins, making the holes obsolete.
Netzspannung
100V
Netzfrequenz
50, 60Hz
Description
The Type B electrical plug has two flat parallel pins and a round grounding (or earth) pin. The earth pin is longer than the other two so that the device is grounded before the power is connected. As with the type A plugs, the American and Japanese versions vary slightly. Type B plugs are rated at 15 amps.
This website only uses the most necessary cookies to enhance your browsing experience. Please accept the use of cookies on this site, to allow us improving the site for you. You will find more information about cookies in the Privacy Statement