Radio Type Approval, Homologation, Certification Services - Global Market Access Solutions
We can offer you reliably all services concerning Type Approval in New Zealand (Wellington). Our distinguished contact with the authority in New Zealand (Wellington), our good relationship to Radio Spectrum Management (RSM), as well as the qualification in the homologation of consumer and automotive RF-products and Short Range Devices (SRD) in ISM-Frequency band will create your market access in New Zealand trouble-free and cost-effective.
We will assist you to put your product successfully on the market by offering the following services:
Identify applicable requirements for your specific product or technology feature to comply with current regulations in safety, EMC, wireless, etc.
Provide pre-compliance testing during the design and development phase to determine compliance
Assist in completion of applications and other required forms
Test in our accredited labs or your qualified facilities to issue CB Test Report and Certificate with applicable national differences and other test reports for wireless, etc.
Handle entire submittal process including working with local testing and certification organizations
Arrange for initial factory inspections that are required before certification issuance
Coordinate verification testing on qualified products as needed
Facilitate and expedite project progress with support of IB-Lenhardt AG local team and/or partner
Support renewal maintenance of certificates as needed
User manual translation service when needed
For New Zealand we can offer you a short termed tentative offer based upon a submitted Datasheet of the device: email@example.com
Due to the increased use of WLAN (Wireless Local Area Network) in New Zealand, Radio Spectrum Management (RMS) has opened a public consultation seeking feedback on their preliminary views and proposals for the 5925 MHz - 7125 MHz frequency range.
RSM proposes to authorise the General User Radio Licence (GURL) for Short Range Devices (SRD) to cover low power and very lower power WLAN devices in the range 5925 - 6425 MHz:
Low Power devices operating at 24 dBm for indoor use only
Very Low Power devices operating at 14 dBm for all locations
Comments shall be submitted no later than 5pm on 30th of June 2021 per email to: Radio.Spectrum@mbie.govt.nz with subject line: “Consultation Submission - WLAN use in the 6 GHz band”
New General User Radio License for Short Range Devices
On 6 November 2020, a new General User Radio License for Short Range Devices (GURL for Short Range devices) came into force by being published in the official Gazette of New Zealand.
In comparison to the 2019 version, the following amendments were made:
- the use of the frequencies 0.1485 – 30 MHz for wireless power transfer systems and induction loop systems for the detection of foreign objections has been regulated
- a new provision for the use of the frequency range 1785 – 1805 MHz for wireless microphone, in-ear monitor, or wireless audio transmitter devices
- in order to implement WRC-19 Resolution 229: amendments to regulation of wireless LAN outdoor use of 5150 – 5350 MHz devices with a power level up to 0 dBW were made
- the use of 13.553 – 13.567 MHz RFID transmitters has been regulated
The Radio Spectrum Management of the New Zealand Ministry of Business, Innovation and Employment has emitted a discussion paper entitled "Adding new usages to General User Radio Licence for Short Range Devices below 30 MHz".
This technical consultation aims at clarifying the existing technical conditions in the general user radio licence (GURL SRD) for a specific field, wireless charging. This technology includes wireless power transfer (WPT) system and inductive loop system, operating in sub 30 MHz frequency range.
The different frequency ranges of WPT already fall implicitly within the current provisions of the GURL SRD. But the inductive loop systems operate within a wide range (0.1485-30 MHz) across many provisions within the GURL SRD.
To clarify the proper use of radio spectrum wireless charging, there is a need to add a new provision to the GURL SRD explicitly covering both entire frequency ranges.
Comments are expected until 2018-09-14 at 5pm (local time),
The Type I plug has two flat pins in a V-shape as well as a grounding pin. A version of the plug, which only has the two flat pins, exists as well. The Australian plug also works with sockets in China. Australia’s standard plug/socket system is rated 10 amps but a plug/socket configuration rated 15 amps also exists, although the ground pin is wider. A standard 10 amp plug will fit into a 15 amp socket but not the other way around.